Fixora XF10 packs a screwdriver, a micro drill and a rotary grinder into one pen-sized body, and the case beside it holds 170 bits and accessories for the three jobs. Three modules set the speeds.
Fixora XF10
3-in-1 electric multi-tool · Screwdriver, micro drill and rotary grinder modules with 170 bits and accessories
Price: $109 Super Early Bird (save $89, 45% off)
Where to buy: Back on Kickstarter
Backers have pushed the campaign past double its goal, with more than $7,300 pledged from 72 backers and the clock running to November 30.
A loose screw, a tiny hole, one last rough edge on a fresh print. Each one normally sends a hand into a different drawer. FIXORA’s designers, engineers and makers built the XF10 around that frustration, and the campaign funds larger production runs, final quality checks and packaging for backers worldwide. The team shares progress, milestones and production updates with backers as the run moves forward.
Three modules, three speeds, no single motor compromise
Each module carries its own gearing, so the screwdriver turns slowly, the drill turns faster and the grinder spins at a speed the other two never approach. Swaps happen by hand. One motor setting stretched across all three jobs would serve none of them well, and dedicated modules keep each speed inside the range its work actually needs. The workflow runs assembly, drilling, then finishing in one sitting.

Electronics repair and model making sit at the center of its job list, with household fixes around them.
The campaign’s job list runs wider than the bench, covering RC and drone maintenance, 3D printing cleanup, DIY crafts, leather work and fine sanding and polishing jobs at home.
The screwdriver turns at 170 RPM and twists by hand

Control defines this module. At 170 RPM the electric drive tightens and loosens screws without the snap that strips a tiny head or cracks a post.
A manual twist mode covers the first turn and the last one, the two moments where feel counts most and powered speed turns clumsy. More than 100 screwdriver bits ride in the kit, shaped for keyboards, electronics and eyeglasses. The same bits handle the ordinary household screws that fill a week, from a loose cabinet hinge to a wobbling drawer pull in the kitchen.
Feel comes first here.
A 940 RPM drill and a grinder that reaches 28,000 RPM
The drill module turns at 940 RPM and takes small drill bits sized for pilot holes, model parts and the single wall-hook hole a household keeps postponing. Holes stay small here.

The module suits thin material and detail work, and a full-size drill still owns joists, masonry and anything structural in a house. Grinding runs far faster.
The rotary module reaches 28,000 RPM for sanding, polishing, deburring and engraving with compatible attachments, and fresh 3D prints give it steady work around the bench. Rough layer lines smooth down, sharp edges lose their bite, and stone, metal and crystal details take a finish fingers alone can’t reach, down to a chipped manicure edge.
Drill bit sizes vary across the kit, sorted beside the screwdriver bits so a pilot hole and the screw that follows it come from the same case. A wall hook, a model kit and a loose bracket all draw from that one tray.
One case holds 170 bits and the controls stay simple
Organization carries the kit. Every bit and accessory sits in a molded slot inside one case, so the right tip surfaces in seconds instead of hiding under a bench lip. Nothing rattles loose inside a tool roll on the way to a job across town.

Three control modes cover the range of work, from a manual twist for delicate positioning to a button press for powered rotation. Forward and reverse both sit on that button.

Auto Mode runs the tool continuously without a held button. Hands stay free to hold the workpiece, guide the bit or catch the screw before it drops behind the bench and vanishes or rolls under the cabinet. Nothing hides in a drawer.
A removable battery, two power modes and a March delivery estimate
The 1,400mAh battery lifts out of the body, and a charged spare drops in when a session runs long at the bench. Corded running covers the rest. Its small display reads the charge in percent, so a swap never arrives as a surprise in the middle of a job.

Plugged into a USB power bank or a desk adapter, the XF10 works while it charges, so a flat battery never ends a session outright at the wrong moment. Pledges start at $109 for the Super Early Bird single, and the cheaper $99 Launch Special tier has already sold out to its 50 backers. A two-pack pledge suits a bench-and-bag split, with one kit at home and a second kit riding along to the workshop across town.
Shipping fees get collected separately through PledgeBox after the campaign closes, the campaign charges no additional taxes, and delivery sits estimated for March 2027. FIXORA also notes that some campaign visuals are AI-assisted renders, with final product photography still to come before production wraps up for backers. Backers in every region can pledge, since the rewards ship anywhere in the world.
Fixora XF10, two-pack
Two 3-in-1 electric multi-tools · One for the bench, one for the bag, each with the 170-piece bit kit
Price: $218 Super Early Bird two-pack (save $178, 45% off)
Where to buy: Back on Kickstarter
Back the XF10 at $109 if small repairs, electronics and model work fill your bench and three separate powered tools feel like clutter on it. Skip it if your jobs start at framing lumber.