OtterBox Armor 1900 PDA Case Review

We use affiliate links. If you buy something through the links on this page, we may earn a commission at no cost to you. Learn more.

Product Requirements:
A PDA that measures under 5.5" long x
3.5" wide x 0.9" deep

When I reviewed the OtterBox
Armor 3600
back in 2003, there was no doubt in my mind that I had just discovered the "Humvee
of PDA Protection." No case I had seen, or that I have since seen, has even come
close to offering delicate electronics such perfect protection when they
are used in abnormally harsh conditions.

However, this solution was aimed more at larger sized PDAs, such as the
HP iPAQ 5455,
which I used for testing at the time. Those with shorter or more shallow devices
would have found the Armor 3600 to be a bit of oversized overkill, though I am
sure that there were some who went ahead and used one anyway, out of necessity.

Now OtterBox is offering a rugged solution for the more compact PDAs and the
people that use them in extreme conditions, the
Armor 1900.

otterbox armor 1900 case1 
otterbox armor 1900 case2 
otterbox armor 1900 case3

Like the 3600 model previously reviewed, the Armor 1900 is not a case for
those that only need to add a bit of screen protection to their PDA. It is for
people who have to cope with the harshest conditions that can be thrown at them,
as they are using their electronic device.

The OtterBox site lists the features of the Armor 1900 as:

  • Universal fit for newer smaller form-factor PDAs
  • Waterproof, crushproof, drop-proof ergonomic design
  • Flexible, fully sealed interactive screen membrane
  • Quick access to CF and SD slots through the top of the case
  • Quick access to PDA connection through the bottom of the case
  • Adjustable neoprene hand strap
  • External stylus holder
  • Flip-up hard screen cover
  • Headphone/headset access
  • Easy open compound latch system
  • Gore membrane vent
  • Fully expandable for all accessories
  • Unconditional lifetime guarantee
  • To begin, the Armor 1900 has a very rugged appearance. Available in either
    Midnight Black and Fluorescent Yellow and accented with gray, this case has an
    abundance of latches, sealed ports and usable features.

    Lets take a look and see if the 1900 lives up to its predecessor…

    Universal fit for smaller form factor PDAs:

    The Armor 1900 measures 6.57" (16.7cm) tall x 4.64" (11.8cm) wide x 2.2"
    (5.6cm) thick at it’s largest points. Its interior is shaped so that it can hold
    a device measuring no more than 5.6" (14.1cm) tall x 3.5" (9cm) wide x 0.9"
    (2.4cm) deep.

    Instead of using a series of removable pads to push the PDA to the front of
    the case, the Armor 1900 uses a clever Velcro strap suspension system which
    keeps the PDA tightly held next to the replaceable write-through membrane and
    it’s plastic border.

    otterbox armor 1900 case4 
    otterbox armor 1900 case5

    Flexible, fully sealed
    interactive screen membrane
    :

    otterbox armor 1900 case6
    otterbox armor 1900 case7

    The membrane is a thin sheet of clear flexible
    plastic. You can write on it directly with a PDA stylus. As long as you don’t
    write so heavily that you gouge holes into the membrane, it will remain
    waterproof. Over time, this membrane will probably show wear, and when that
    happens replacements can be
    ordered.

    The interior of the case is composed of unlined plastic, but since the PDA
    should not really touch anything but the screen membrane, its plastic border and
    the Velcro suspension system, it is unlikely that the PDA will become scratched
    while in the case.

    As you might have guessed by the case’s name, the
    HP iPAQ 1900
    series perfectly fits…

    otterbox armor 1900 case8

    A flip-up cover protects the touch screen when it is not being written upon.

    Flip-up hard screen cover:

    As mentioned, the screen of the PDA is protected by a
    clear plastic flip-lid. This cover will swing approximately 180º,
    either in the down and fully closed position, or standing straight up. I was
    pleasantly surprised to find that the lid would more or less stay up on its own
    when flipped to the upward position, but I suspect that over time it will not
    keep the same tension. Missing is the more secure closure system that the Armor
    3600 utilized. By this, I mean that the flip lid is not held securely shut when
    it is in the down position, it can be easily raised..

    otterbox armor 1900 case9

    Waterproof, crushproof,
    drop-proof ergonomic design
    :

    Here you can see it in our hot tub. So yes, I would
    call it waterproof and the Armor 1900 also floats.

    otterbox armor 1900 case10

    According to the OtterBox website, "All OtterBox cases
    – from the original OtterBox case to the innovative Armor 3600 for PDA
    protection — feature a closed-cell neoprene o-ring that seals out water – no
    matter how harsh the conditions. Independent tests show OtterBox cases keep
    valuables dry to depths of 110 feet – even in chilly Alaskan waters."

    The case is crushproof in the sense that heavy items
    will not cause it to collapse upon the PDA. I tested this by once again
    convincing Steve to balance his 200 pounds on the screen cover of the case.
    However, the Armor 1900 is so much smaller than the 3600 previously tested that
    he wasn’t able to put both feet on it…

    otterbox armor 1900 case11

    I didn’t care to drive over the case or put it under what might be
    considered a truly destructive crushing weight, but for those of you that
    want to know if the Armor 1900 can take that kind of abuse, there is a picture
    of an Otterbox under a Jeep’s wheel on their website…

    otterbox armor 1900 case12
    photo courtesy of OtterBox

    Drop proof? Yes, and for two reasons…

    Adjustable neoprene hand strap:

    First, because if you are using the strap attached to
    the back of the case there is virtually no chance that you will drop the
    enclosed PDA. The hand strap is made of thick stretchy neoprene with adjustable
    Velcro ends that fold back upon themselves for a perfect fit. When using the
    strap, the case is securely held in the user’s hand, with virtually no chance of
    being dropped.

    otterbox armor 1900 case13

    Of course, if the user needs a more hands-free way to
    carry the case, there is also an optional neck lanyard kit.

    otterbox armor 1900 case14
    photo courtesy of OtterBox

    The second reason that the case is drop-proof is
    because if the user happens to be a total klutz (like me), the case will survive
    a long fall onto concrete without the PDA inside getting damaged. Yes, I did try
    that test out multiple times (on purpose) from about a height of 4′ onto
    a wooden floor. The PDA and case survived in fine shape, though on about the
    fifth drop the flip lid did pop off..

    Quick access to CF and SD slots
    through the top of the case
    :

    The entire clear top of the Armor 1900 can be opened
    to allow direct access to the SD or CF card slots at the top of the PDA.

    otterbox armor 1900 case15 
    otterbox armor 1900 case16

    There are even different sized PODs available that can
    accept taller GPS cards or scanning modules that may need to be added to the
    PDA.

    otterbox armor 1900 case17 
    otterbox armor 1900 case18 
    otterbox armor 1900 case19
    From left to right: large POD, medium POD, and the Scanner POD
    with a hardened scratch-resistant lens, photos courtesy of OtterBox

    The only area where you might find that there is limited to non-existent
    accessibility is in regard to the voice record button and the Infrared port. On
    the iPAQ 1945, these are both located on the left side, which is of course
    covered by the hard case. The record button can be re-mapped if you need it, but
    there is no way around the placement of the Infrared port – you’ll just have to
    do without using it when the PDA is in the Armor 1900. I hardly ever even use my
    IR port, so it’s not that big of a deal to me.

    Headphone/headset access:

    There is a rubber plug on the left side that a headset
    cord can be threaded through. Once the cord is through and the plug has been
    replaced, the PDA is once again safe from water, dust and dirt.

    otterbox armor 1900 case20 
    otterbox armor 1900 case21

    Note the rubber gaskets that are present on all of the removable pieces of
    the case. These are a major line of defense against dust, dirt and water. They
    should always be kept clean and periodically inspected for deterioration.

    Quick access to PDA connection
    through the bottom of the case
    :

    Unlike other ruggedized cases that require the removal
    of the PDA for syncing or charging, the Armor 1900 has a large rubber plug that
    pops off the bottom to allow direct access to the port.

     otterbox armor 1900 case22 
    otterbox armor 1900 case23

    There is even a serial port connection that can be
    added to the bottom of newer model iPAQs that share the standard 22 pin bottom
    connector.

    otterbox armor 1900 case24
    photo courtesy of OtterBox

    External stylus holder:

    The left side of the case has a molded rubber stylus
    holder, which will keep the use from having to keep one stowed in their pocket.
    This also allows the user to use a slightly thicker stylus than the one that
    fits in their PDA’s silo.

    otterbox armor 1900 case25

    Easy open compound latch system:

    The latches found on the back of the case and on the top are all heavy duty
    plastic that requires pieces about to be held together to be fitted in correctly
    – creating a seal. Then the latches are clamped down and locked. These latches
    are stiff, and will not come undone unintentionally, yet they are easy enough to
    operate when access is needed.

    otterbox armor 1900 case26 
    otterbox armor 1900 case27 
    otterbox armor 1900 case28

    Each latch has a hole in it’s stem so that you can lock it down with the
    included hex screws and allen wrench.

    otterbox armor 1900 case29 
    otterbox armor 1900 case30

    An extra rubber plug for the headset hole is also included.

    Gore membrane vent:

    Inside the case’s back wall is a covered vent. I assume (always dangerous)
    that this is to help keep condensation from appearing on the screen of the PDA
    when it is moved from one temperature extreme to the next.

    otterbox armor 1900 case31

    Fully expandable for all accessories:

    There are any number of
    accessories
    available for the Armor 1900 that will make it even more adaptable to any use
    that someone can dream up. Items like belt clips, the preciously mentioned
    larger GPS or scanner pods that attach to the top, neck lanyards, a serial port
    adapter, as well as various vehicle mounting solutions are available. It would
    be very easy to spend twice the amount of the case adding accessories, but the
    ability to do so makes this case all the more valuable.

    One benefit of a case like this is that instead of spending big money
    on a ruggedized PDA that will most likely be running an older OS or worse – not
    have a color screen, the end user can instead instantly ruggedize any PDA that
    they already own, or will eventually buy, simply by placing it in this case.

    Unconditional lifetime guarantee:

    According to the OtterBox site, "If your OtterBox product fails for any
    reason, call us at 888-695-8820 and we’ll gladly replace it. We stand behind our
    cases 100%."

    Once again, I think that OtterBox has set the standard for ruggedized PDA
    cases. I believe that the Armor 1900 lives up to every one of its claims,
    and I doubt that there is a better PDA case available for people that need
    ultimate protection either because of their jobs or their pastimes. If you are
    the type of person that have a typical job in a sterilized environment, and you
    need a case that can protect your PDA from a herd of elephants or a  sudden
    squall and you have a smaller PDA, then the
    OtterBox Armor
    1900
    is the case for you. Don’t forget that if you have a larger device and
    you need the ultimate in protection, you can always get the
    Armor 3600.

    Price: $99.95
    Available in black or yellow

    Pros:
    Rugged, waterproof/dustproof/crushproof  protection for your PDA
    Many accessories to make case work for your unique needs
    Easy access to most ports on the PDA

    Cons:
    No access to Infrared port
    It’s big and expensive – but if you need it, that won’t stop you

     

    Product Information

    Price:99.95
    Manufacturer:OtterBox
    Pros:
    • Rugged, waterproof/dustproof/crushproof  protection for your PDA
    • Many accessories to make case work for your unique needs
    • Easy access to most ports on the PDA
    Cons:
    • No access to Infrared port
    • It's big and expensive - but if you need it, that won't stop you

    1 thought on “OtterBox Armor 1900 PDA Case Review”




    1. Gadgeteer Comment Policy - Please read before commenting

    Leave a Comment

    Your email address will not be published. Required fields are marked *